- 110v 175w silicone hot pad
Parts: Heater Core
Type: Electric Heater
Interchange Part Number: Wire length: 200cm
Manufacturer Part Number: Compressive strength: 1500v/5s
Other Part Number: Material: Alloy wire,Silicone rubber
Special Features: Power:0-110v 0-175w
Country/Region of Car Manufacture: all over the word
Heater size:: 13cm x 9cm
The silicon rubber heater is mainly composed of nickel chromium alloy electric heating wire and high temperature silicon rubber insulation layer. Silicone rubber high temperature insulation layer is made of silicone rubber and glass fiber cloth composite and into a thin sheet (1.5mm), silicone rubber heater has a good flexibility.
＞Fast heating, uniform temperature, high thermal efficiency, high strength, easy to use, safe life for up to four years, not easy to aging.
＞The silicon rubber heater can be used in the wet, non explosive gas environment, industrial equipment, pipelines, tank barrels with heat insulation (oil heater).
＞Can be directly tied to the surface of heated objects.
＞Wire and Pad heater all made by High-temperature resisting silicone. Ensure long-term use. Oil and acid resistant, Waterproof.
＞Built-in highest quality thermal overload protection switch for Power saving. Additional safety. Fast heat rises.
＞Keeps engine oil warm. Prevent cold start damage, reduce engine wear.
＞3M high temp adhesive on reverse side, easy to install.
＞This heater is significantly more efficient and better than a conventional tank heater.
＞Can be used as the auxiliary heating of the refrigeration and air conditioning compressor, motor and other equipment.
Material: Alloy wire,Silicone rubber
Heater size: length:13cm width:9cm
Wire length: 200cm
Insulation material the highest resistance temperature: 300 degrees
Power error: 8%
Insulation resistance:≥5 MΩ
Compressive strength: 1500v/5s
Resistance voltage: 6KV
INSTALLATION INSTRUCTIONS FOR SILICONE HOT PAD HEATER:
1. CLEAN AND SAND RESERVOIR TO BARE METAL. REMOVE ALL DIRT, GREASE, OIL AND
OTHER CONTAMINANTS USING A DEGREASING SOLVENT. DO NOT USE GASOLINE OR
2. IF HEATER IS TO BE INSTALLED ON A VEHICLE, TRY TO RUN THE ENGINE TO PRE-WARM
THE OIL PAN.
3. PEEL OFF BACKING AND APPLY PAD TO RESERVOIR MAKING SURE THAT THERE ARE NO
AIR POCKETS OR CREASES IN THE PAD. USE A ROLLER OR SPREADER TO REMOVE THEM.
4. SEAL THE EDGES OF THE HEATER WITH HIGH TEMPERATURE SILICONE TO INSURE
PROPER PROTECTION TO THE EDGE OF THE HEATER.
5. SECURE THE CORD UP AND OUT OF THE WAY OF ANY OBSTRUCTIONS, MAKING SURE
THAT IT DOES NOT HANG DOWN FROM THE PAN OR TOUCH ANY HOT OR MOVING
1. Do not cut pad.
2. Do not use on batteries
3. This heater can only be used on a metal pan or tank with a smooth float surface.. It should never be installed on a plastic or poly container.
1 PC Heater Pad (not with plug)
Electric Mini Travel Hot Water Kettle Silicone Gel Foldable Automatic Power-off Camping Portable Boiler With Cup 110V 220V
Free shipping Flex PVC Banner Welding machine for banner joint 110V/220V avaliable Hot air welder Welder
JCD hot air gun 220V 110V Heat Gun Rework soldering station 8858 650W Hot Air Blower Ceramic Heater nozzle
New EazzyDV IB-175W 25pcs LED Lights Bulb HD ONVIF WIFI IP Camera Email Alarm P2P Night Vision surveillance
Electric Water Kettle Portable Silicone Folding Hidden Handle Mini Insulation 110V-240V Adjustable Temperature
YIHUA 110V/220V EU/US PLUG 938D Portable Hot Tweezers Mini Soldering Station Tweezer For BGA SMD Repairing